Model PG1000L
1-piece Superglide Transmission Case with Internal Liner

$925.00

This is simply the best 1-piece Powerglide transmission case available. You will not find another case with a better combination of strength, simplicity, light weight, and unsurpassed quality in casting and machining. Here's why:

• No bulky external shield required because the safety liner insert makes it SFI 4.1 Certified*.
• No flexplate shield required because our bellhousing is SFI 30.1 Certified*.
• Uses all stock and aftermarket internals; no oddball parts.
• Bellhousing is part of the case just like the Powerglide so all machining alignment remains perfect.
• Made by a permanent mold process from heat treated aircraft grade aluminum. This process is stronger, more ductile, and more accurate than competitors' brittle sand castings.
• Oil pan flanges are thickened to stiffen case. Beefed up oil pump area prevents front case distortion under high horsepower. Minimizes flexing which causes gear misalignment and breakage. This case does not leak!
• Oil pump mounting bolt holes heli coiled to prevent thread failures.
• Patented adjustable transbrake release. Adjustment bolt varies both the quickness and the rate of release which varies the reaction time and the hit of the tires.
• Predrilled for double dump transbrake.
• Redesigned oil passages radically improves release time of the transbrake and allows instant application.
• Patented reverse piston bleed hole vents air from piston area and increases transbrake consistency.
• No need for external shields or bottom straps.
• Each case is thoroughly inspected at every step of its production. You can be assured that you will not have the problems associated with porosity and misalignment from poor castings or inferior machining as with other cases.

Model PG1000RL
1-piece Superglide "Roller" Transmission Case with Liner

Reid Racing now offers the incredibly popular Superglide transmission case with a factory installed needle roller bearing in the hub.

$975.00

• All the same features of our original Reid Racing Superglide listed above.
• Special high speed caged roller bearing replaces the OEM bushing to enhance long life and ensure the smoothest operation.
• A perfect match to aftermarket roller bearing governor support housings or roller bearing shorty housings.
• The bearing bore is machined at the same time as the hub and reverse piston bore ensuring perfect alignment within one thousandth of an inch.
• Retains both 30.1 and 4.1 SFI certifications.

Model PG2000
2-piece Superglide Transmission Case

Reid Racing's 2-piece Superglide transmission case allows use behind all popular engine combinations.

$795.00

Starting with the time proven 1-piece Superglide, Reid Racing engineers decided against the "cut it in half" approach and specifically designed this case to be used as a 2-piece unit. The full 360 degree reinforced mounting flange provides the needed rigidity and stiffness, while extra thickness in critical areas adds strength to the rear of the case and eliminates the need for an internal liner. Unlike our sand-cast competitors, our permanent mold casting process is used for extremely accurate, tough, porosity-free cases. Adapter bellhousings and flexplates are available for most popular engine combinations; See below.

• No internal or external shields required; case is SFI 4.1 Certified*
• Uses all stock and aftermarket internals; no oddball parts.
• Bellhousings available for Chevrolet, Buick, Olds, Pontiac, Ford, and Mopar engines. Indexing ring on the oversized flange properly centers bellhousing.
• Front pump can be installed with or without the bellhousing attached.
• Made by a permanent mold process from heat treated aircraft grade aluminum. This process is stronger, more ductile, and more accurate than competitors' brittle sand castings.
• Oil pan flanges are thickened to stiffen case. Beefed up oil pump area prevents front case distortion under high horsepower. Minimizes flexing which causes gear misalignment and breakage. This case does not leak!
• Oil pump mounting bolt holes heli coiled to prevent thread failures.
• Patented adjustable transbrake release. Adjustment bolt varies both the quickness and the rate of release which varies the reaction time and the hit of the tires.
• Predrilled for double dump transbrake.
• Redesigned oil passages radically improves release time of the transbrake and allows instant application.
• Patented reverse piston bleed hole vents air from piston area and increases transbrake consistency.
• No need for external shields or bottom straps.
• Each case is thoroughly inspected at every step of its production. You can be assured that you will not have the problems associated with porosity and misalignment from poor castings or inferior machining as with other cases.

Model PG2000R
2-piece Superglide "Roller" Transmission Case

Reid Racing also offers the 2-piece Superglide transmission case with a factory installed needle roller bearing in the hub.

$845.00

• All the same features of our original 2-piece Reid Racing Superglide listed above.
• Special high speed caged roller bearing replaces the OEM bushing to enhance long life and ensure the smoothest operation.
• A perfect match to aftermarket roller bearing governor support housings or roller bearing shorty housings.
• The bearing bore is machined at the same time as the hub and reverse piston bore ensuring perfect alignment within one thousandth of an inch.
• Retains SFI 4.1 certification*.

Model PG2000-400B
2-piece Superglide Back Half Transmission Case with Bushing for Turbo 400 Output Shaft

$845.00

• All the same features of our original 2-piece Reid Racing Superglide listed above.
• This new case gives dramatic strength increase over the standard sized powerglide output shaft and has a high performance bronze bushing.
• For use with any of our 7 bellhousings (shown below).

Model PG2000-400R
2-piece Superglide Back Half Transmission Case with Roller Bearing for Turbo 400 Output Shaft

$845.00

• All the same features of our original 2-piece Reid Racing Superglide listed above.
• This new case gives dramatic strength increase over the standard sized powerglide output shaft and has a roller bearing.
• For use with any of our 7 bellhousings (shown below).

Model BH001
Chevrolet Bellhousing

$195.00

Chevrolet bellhousing for the Reid Racing 2-piece Superglide case fits all 90 degree V8's and the 4.3 liter V6. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block.

Model BH010
Small Block FORD Bellhousing

$295.00

Small block Ford bellhousing for the Reid Racing 2-piece Superglide case fits 1966 and later 289-302-351C-351W-5.0L and 5.8L engines. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block. When used with a Reid Racing flexplate part # FP010 available below, these bellhousings allow for direct fit to the engines with no spacers or adapters needed. Designed for use with a 164 tooth flexplate, stock style starters are used in the factory location.

$395.00

The innovative, patent-pending Reid Racing adapter flexplate for small block Fords eliminates the need for a separate crank adapter by combining the flexplate, crank adapter, converter pilot and ring gear into a single piece of billet steel. This creates a truly bolt-on part. The flexplate bolts directly to the Ford crank, converts to use a standard Powerglide converter, then back to a Ford 164 tooth ring gear size so a stock starter can be used. The flexplate is thicker than stock, has machined holes allowing for proper flex, is plated for rust protection, and the ring gear teeth are hobbed directly into the plate. Being completely CNC machined makes the flattest and most concentric part available, and the dual powerglide / Turbo 400 bolt pattern is predrilled for 7/16" bolts to fit most racing torque converters. SFI 29.1 approved* for competition use. Uses ARP part # 200-2807 crankshaft bolts, available separately.

ARP200-2807
Small Block FORD Crankshaft Bolts (6)
$17

Model BH020
Big Block FORD Bellhousing

$295.00

Big block Ford bellhousing for the Reid Racing 2-piece Superglide case fits 429 and 460 Fords. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block. When used with a Reid Racing flexplate part # FP020 available below, these bellhousings allow for direct fit to the engines with no spacers or adapters needed. Designed for use with a 164 tooth flexplate, stock style starters are used in the factory location.

$395.00

The innovative, patent-pending Reid Racing adapter flexplate for big block Fords eliminates the need for a separate crank adapter by combining the flexplate, crank adapter, converter pilot and ring gear into a single piece of billet steel. This creates a truly bolt-on part. The flexplate bolts directly to the Ford crank, converts to use a standard Powerglide converter, then back to a Ford 164 tooth ring gear size so a stock starter can be used. The flexplate is thicker than stock, has machined holes allowing for proper flex, is plated for rust protection, and the ring gear teeth are hobbed directly into the plate. Being completely CNC machined makes the flattest and most concentric part available, and the dual powerglide / Turbo 400 bolt pattern is predrilled for 7/16" bolts to fit most racing torque converters. SFI 29.1 approved* for competition use. Uses ARP part # 350-2802 crankshaft bolts, available separately.

ARP350-2802
Big Block FORD Crankshaft Bolts (6)
$19

Model BH030
Buick, Oldsmobile, Pontiac Bellhousing

$295.00

Buick/Olds/Pontiac bellhousing for the Reid Racing 2-piece Superglide is not a dual-pattern bell, which allows for a perfect fit to all Buick, Oldsmobile, and Pontiac V8's without unused bolt holes and awkward castings. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block. Starter pockets on both sides allow for driver or passenger side starter locations. No special flexplate is required.

Model BH040
Big Block MOPAR Bellhousing

$295.00

Big block Mopar bellhousing for the Reid Racing 2-piece Superglide case fits 361-383-400-413-426-440 B and RB series engines including the 426 Hemi. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, and a contoured mounting flange to properly match the rear of the engine block. The flange area is large enough to access Chevrolet-size flexplates.

Model BH050
Modular FORD Bellhousing

$295.00

Modular Ford bellhousing for the Reid Racing 2-piece Superglide case fits 4.6, 5.4, and 6.8 liter overhead cam engines. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block. When used with a Reid Racing flexplate part # FP050 available below, these bellhousings allow for direct fit to the engines with no spacers or adapters needed. Designed for use with a 164 tooth flexplate, stock style starters are used in the factory location.

$395.00

The innovative, patent-pending Reid Racing adapter flexplate for Modular Fords eliminates the need for a separate crank adapter by combining the flexplate, crank adapter, converter pilot and ring gear into a single piece of billet steel. This creates a truly bolt-on part. The flexplates bolt directly to the Ford 6-bolt or 8-bolt crank, converts to use a standard Powerglide converter, then back to a Modular 164 tooth ring gear size so a stock starter can be used. The flexplate is thicker than stock, has machined holes allowing for proper flex, is plated for rust protection, and the ring gear teeth are hobbed directly into the plate. Being completely CNC machined makes the flattest and most concentric part available, and the dual Powerglide/Turbo 400 bolt pattern is predrilled for 7/16" bolts to fit most racing torque converters. SFI 29.1 approved* for competition use. 6-bolt flexplates use ARP part # 151-2801 crankshaft bolts available separately. 8-bolt flexplates use part # 151-2801-8.

ARP151-2801
Modular FORD Crankshaft Bolts (6)
$14.62

ARP151-2801-8
Modular FORD Crankshaft Bolt (8)
$19.50

Model BH060
Small Block MOPAR Bellhousing

$295.00

Small block Mopar bellhousing for the Reid Racing 2-piece Superglide case fits 318, 340, and 360 series engines. Cast from high-strength aluminum and heat treated for additional toughness, the bellhousing passes the stringent SFI 30.1 certification* and is approved with no external shields required. The bell weighs only 12.6 pounds, features an open bottom for easy converter access, a reduced diameter for better floorboard clearance, and a contoured mounting flange to properly match the rear of the engine block.