Model D44001CL (left)
Model D44001CR (right)
CHEVY Heavy Duty Flat Top Dana 44 Knuckles

$219.00 each

• Chevy/Jeep spindle bolt pattern accepts "outers" from all open knuckle Chevy and Jeep Dana 44, Dana 30, and 10-bolt front ends to 1986
• Cast from high strength ductile iron
• Beefed up with extra material and ribbing
• Flat tops machined and drilled for high steer arms
• 4th bolt hole for high steer arms increases clamping force and sheer strength (3 hole high steer arms still fit) For 4 hole steering arm distributors click here
• 3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
• Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
• Tapered tie rod holes accept factory tie rod ends
• Tie rod holes can be drilled to accept 3/4" heim ends
• Powder coated bright orange for long lasting looks
• Interchangeable with all factory and aftermarket Dana 44 components
• Fully machined and ready for installation
• Machined to clear CTM u-joints without removing the grease fittings
• Tie rod hole is tapered from the top to the bottom

Will fit 10-bolt and early Dana 30 axles with minor modification.

Dealer inquiries welcome. Knuckles for off road use only.
There is no warranty on this product.

Model D44001FL (left)
Model D44001FR (right)
FORD Heavy Duty Flat Top Dana 44 Knuckles

$249.00 each

• Cast from high strength ductile iron
• Beefed up with extra material and ribbing
• Flat tops machined and drilled for high steer arms
• 4th bolt hole for high steer arms increases clamping force and sheer strength (3 hole high steer arms still fit) For 4 hole steering arm distributors click here
• 3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
• Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
• Tapered tie rod holes accept factory tie rod ends
• Tie rod holes can be drilled to accept 3/4" heim ends
• Powder coated bright orange for long lasting looks
• Interchangeable with all factory and aftermarket Dana 44 components
• Fully machined and ready for installation
• Tie rod hole is tapered from the bottom to the top
• Based on the Bronco disc brake knuckle and fit 1/2 and 3/4 ton brakes
• The only aftermarket knuckle available for a Ford Dana 44.

Model D44001SL (left)
Model D44001SR (right)
SCOUT Heavy Duty Flat Top Dana 44 Knuckles

$249.00 each

• Cast from high strength ductile iron
• Beefed up with extra material and ribbing
• Flat tops machined and drilled for high steer arms
• 4th bolt hole for high steer arms increases clamping force and sheer strength (3 hole high steer arms still fit) For 4 hole steering arm distributors click here
• 3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
• Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
• Tapered tie rod holes accept factory tie rod ends
• Tie rod holes can be drilled to accept 3/4" heim ends
• Powder coated bright orange for long lasting looks
• Interchangeable with all factory and aftermarket Dana 44 components
• Fully machined and ready for installation
• Machined to clear CTM u-joints without removing the grease fittings
• Same as the Chevy 44 knuckles but have the 8 bolt spindle pattern

Model D44002CR (right)
CHEVY Stock Replacement Heavy Duty Flat Top Dana 44 Knuckle

$219.00 each

• Chevy/Jeep spindle bolt pattern accepts "outers" from all open knuckle Chevy and Jeep Dana 44, Dana 30, and 10-bolt front ends to 1986
• Based on our Heavy Duty Chevy Dana 44 knuckles
• Cast from high strength ductile iron
• Beefed up with extra material and ribbing
• Designed to be a direct replacement for a passenger side Chevy Dana 44 knuckle
• Flat tops machined and drilled for 3-hole high steer arms, not raised the additional 3/8" for high steer tie rod to leaf spring clearance as are our other Dana 44 knuckes.
• Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
• Top-to-bottom tapered tie rod hole accepts factory tie rod ends
• Tie rod hole can be drilled to accept 3/4" heim ends
• Powder coated bright orange for long lasting looks
• Fully machined and ready for installation
• Machined to clear CTM u-joints without removing the grease fittings

Will fit 10-bolt and early Dana 30 axles with minor modification.

Model D44003CL (left)
Model D44003CR (right)
CHEVY "ARMLESS" Heavy Duty Flat Top Dana 44 Knuckles

$219.00 each

• Based on our Heavy Duty Chevy Dana 44 knuckles
• Chevy/Jeep spindle bolt pattern accepts "outers" from all open knuckle Chevy and Jeep Dana 44, Dana 30, and 10-bolt front ends to 1986
• Cast from high strength ductile iron
• Beefed up with extra material and ribbing
• Flat tops machined and drilled for high steer arms
• 4th bolt hole for high steer arms increases clamping force and sheer strength (3 hole high steer arms still fit) For 4 hole steering arm distributors click here
• 3/8" thickness added to flat top of the knuckle for high steer tie rod to leaf spring clearance
• Cast-in DUAL steering stops eliminate bent stop bolts that can cause u-joint and axle failures
• "Armless" design comes from customer requests; reduces weight, provides clearance when stock steering arms are no longer needed.
• Powder coated bright orange for long lasting looks
• Interchangeable with all factory and aftermarket Dana 44 components
• Fully machined and ready for installation
• Machined to clear CTM u-joints without removing the grease fittings

Will fit 10-bolt and early Dana 30 axles with minor modification.

Dealer inquiries welcome. Knuckles for off road use only.
There is no warranty on this product.